How to Build an Aluminum Mini Blinds Stand – Part II: How to Make Them!

by Ben Greenfield from IGNPosted September 12, 2018 10:24:40I’ve been looking around for a way to make these mini blinders work, and I came up with a really simple solution.

You know, the sort of thing you can buy from a hardware store and install yourself.

You take a piece of aluminum and weld it to the bottom of the blinds.

That creates an anchor point and the mini blind is anchored by the anchor point.

When you’re ready to assemble the blind, you just grab that piece of metal and pull it up onto the blind so it’ll sit securely in place.

The result is a very simple piece of hardware that’s very versatile.

It can be used as a doorstop, as a curtain rod, or just as a way for the blind to hang down.

The next step is to figure out how to make them.

You need to cut out a few holes that’ll allow the blind mount to sit flush with the floor.

Once you’ve drilled out the holes, you’ll need to drill two holes in the top of the base that will be the “eyes” of the mini Blind.

Once the holes are drilled, you’re all set to start assembling the blind.

First off, you need to assemble your aluminum blind.

You’ll need some wood for the base, some screws for the screws, some nuts, some bolts, some zip ties, some wire, some tape, and a couple of zip ties.

You also need some screws that hold the aluminum base in place when the blind is assembled.

The nuts and bolts will be attached to the base by the two metal brackets.

The zip ties will hold the base in position.

You’ll need about a half-gallon of clear solvent.

Use a small amount of clear, and let it sit in a bucket of cold water for about 10 minutes.

It’s okay to let it soak for an hour, but just be careful not to let the solvent get into the water.

Once it’s fully saturated, take it out of the water and pour it into the clear solvent bucket.

The solvent will settle to the top and you should see a clear solution form.

Now, take your aluminum base and lay it out in a square planter.

Put a sheet of aluminum foil on top of it.

The foil will help hold the blind in place during assembly.

You can use a flat surface, or use some scrap wood.

I’m sure you’re thinking that the aluminum blind base is pretty simple.

I’m sure that you’re probably thinking the same thing as well.

It is simple.

But it isn’t simple to assemble.

You’re going to need some tools.

You are going to have to use some kind of drill to make the hole for the aluminum pin.

You will also need to use a drill press to push the aluminum wire through the hole in the base.

You might have to go into the woods with a shovel to get the wire to come out.

There’s a lot to learn when it comes to these little projects.

If you’re really curious about this project, you can always check out my article about making a mini blind.

I’ll be updating this article when I learn more about these projects.

Now, the next step for this is making the bolts.

You may have heard of epoxy or duct tape.

Both of these are great for this, but I don’t have time to cover them here.

If I do, please leave a comment below and I’ll update this post.

If not, I’m going to go ahead and say it’s not that bad.

The bolts are going be pretty simple, but if you’re a DIY person and you’re looking to make some really cool things, I recommend epoxy and duct tape for now.

If, however, you want to make more complex pieces of hardware, I suggest you use something like metal rivets or screws.

These bolts are really easy to make.

You simply attach one end of the rivet to the aluminum piece you’re about to assemble, and then attach another end to the other end of your aluminum piece.

You want to get them just snug enough to keep the rivets from sticking together.

Here’s the process:Attach one end to your aluminum pieces, then attach the other one to the riveting machine.

Attach the metal to the metal piece.

Attach one rivet and attach the next rivet.

You should be done.

You just need to screw the rivetted piece into place, and it should stick right into the base and make a really nice looking screw.

Now it’s time to put the blind on.

You can see that the blind comes out of one of the two holes that are drilled in the aluminum.

Now you just need the next piece of wood that’s going to be the blind holder.

You drill a hole in a piece that’s the same size as the aluminum pieces you’re attaching the