A few weeks ago, I built an aluminum patio deck out of aluminum bars for my garage.
The goal was to have a really nice, shiny surface that I could stand on and enjoy the sunlight while I built up my yard.
But after the first couple of weeks of building it, I noticed that the deck was so uneven and the bars were falling off the rails so fast that it was starting to look like something from a video game.
It’s pretty much like building a video wall.
A couple of years ago, we built a video board out of an aluminum bar, which was actually a great idea, but the bars on it didn’t look right.
So, after building up my garage for a few months, I took the aluminum bar out and put it in the garage.
I didn’t know what to do with it, but I was determined to use it.
After a week or so, I was able to build a deck out the same way I had built the patio deck.
And it was so great, I couldn’t stop playing it.
After seeing how awesome the aluminum patio had looked, I decided to build an aluminum wall.
I wanted a deck that looked like it had been put together by someone with no hands or a big, rusty axe.
What You’ll Need: 1 aluminum bar 1 sheet of aluminum sheet metal (I used the 3-inch-thick piece) 4-inch aluminum tubing 1 4-ounce bucket of wood or other strong material (I did a 2-inch strip of aluminum and cut it in half, so I could fit 4 inches into my garage) 4 feet of 4-by-4-foot aluminum tubing 2 aluminum sheets (or sheets of aluminum) 3 aluminum sheets 2 aluminum sheet screws 3 aluminum sheet nuts 1 aluminum strip cut in half 1 1/2-inch bar of 1/4-inch wood or similar material (about an 8-inch length) 1 1-inch sheet of 3-by 3-foot wood (about a 5-inch height) Aluminum tubing for the patio bars (about 2 feet of it) A 1-pound bar of wood (or similar material) (I cut the bar in half to make two bars) Wood glue (optional) Step 1: Cut the aluminum sheet wood to the length you want the deck to be.
The bars should be at least 1 1 1 / 2 inches tall.
If you want a shorter deck, cut the sheet wood smaller.
For my backyard, I used 4 1 1 4 inch strips of 2-by 4-foot metal to make a long 2-foot-by 6-inch deck.
If you’re not familiar with how to cut sheet metal, here’s a video I made about it.
Step 2: The first step is to remove the strip from the wood.
To do this, lay a sheet of wood on top of the strip.
Then, using a piece of wood hammer, hammer the wood into the strip until it’s completely removed.
You want to make sure the wood is smooth.
Next, drill out the holes in the strip and attach the wood to one end of the bar.
Here’s how it looked: Step 3: Attach the aluminum strips to the bar using the 4- or 6-foot length of wood.
The bar needs to be at a depth of 1 1 3/4 inches.
If it’s longer, you’ll need to drill more holes in it.
Attach it to the sheet metal using the 1-foot strip of 2 inches.
That’s all there is to it!
You can make a great patio deck by cutting out a template from the bottom of your garage.
This template can be used for a variety of reasons.
I used it for the aluminum deck because I wanted something that looked great, but was sturdy enough to be put together on a piece to go with it.
It also has a lot of advantages over the standard patio deck, because you can put the bars in the end, instead of the middle, and the deck will not sag.
Step 4: Now it’s time to put the deck together.
This is where things get really tricky.
The template can also be used to make some other types of bars, like a patio door.
As you can see from the photos, I had to drill a hole in the patio bar, attach the end of a 1-by 2-1/2 inch piece of aluminum to the outside of the deck, and attach some pieces of wood to make the outside door.
It’s very similar to a door you might buy at a hardware store, but there are a few important differences.
First, the doors are going to be 1 1 2 inches wide.
Secondly, the hinges are going be 2 1/8 inches wide, which means that if you don